|  | AM-4250/TRC-97 Radio Frequency Amplifier
Call for price Please visit: www.torontosurplus.com for further details.
This is the amplifier unit for the AN/TRC-97 4.4-5 GHz Tactical Troposcatter Radio.
Call for price
|
|  | Amcron Macro-Tech 2400 Professional Audio Amplifier
$1500.00 US Please visit: www.torontosurplus.com for further details.
This Professional Audio Amplifier delivers an incredible amount of power in a low profile design. This unit offers 520 watts into 8 ohms, 800 watts into 4 ohms, 1,050 watts into 2 ohms per channel (in Stereo mode). And up to 2,070 watts into 4 ohms (in Bridged mono mode).
SPECIFICATIONS:
- Frequency Response: ±0.1 dB from 20 Hz to 20 kHz at 1
watt
- Phase Response: ±10 degrees from 10 Hz to 20 kHz at 1
watt
- Signal-to-Noise Ratio: 20 Hz to 20 kHz: Better than
100 dB below full bandwidth power. A-weighted: Better
than 105 dB below full bandwidth power.
- Total Harmonic Distortion (THD): Less than 0.05% at
full bandwidth power from 20 Hz to 1 kHz increasing linearly
to 0.1% at 20 kHz.
- Intermodulation Distortion (IMD): (60 Hz, 7 kHz) Less
than 0.05% from 163 milliwatts to full bandwidth power.
- Damping Factor: Greater than 1,000 from 10 Hz to 400
Hz
$1500.00 US
|
|  | Amplica VD623601 RF Amplifier, +15VDC
Call for price Please visit: www.torontosurplus.com for further details.
This amplifier has SMA (female) connectors for input & output.
Frequency not known.
2 in stock.
Call for price
|
|  | Amplifier Research 100L LF / RF Power Amplifier
$ 7,895.00 US Please visit: www.torontosurplus.com for further details.
Frequency Response: 10 kHz to 220 MHz
Power Output: 150W (100W cw minimum into 50 ohms)
Flatness: ± 1.5dB at 1.0 milliwatt input
Input Power for Rated Output: 1.0 milliwatt
Power Gain: 50 dB minimum
Primary Power: 115 ± 10% VAC, 50/60 Hz, 30 Amp Service
RF Connectors: Input - BNC (f), Output - N (f)
$ 7,895.00 US
|
|  | Amplifier Research 1W1000 RF Amplifier
$ 1075.00 US Please visit: www.torontosurplus.com for further details.
A solid state, self-contained, air-cooled, broadband amplifier designed for applications where instantaneous bandwidth and high gain are required.
Provides a minimum of 1.0W of swept power when used with an RF sweep generator.
Provides readily available RF power for typical applications such as RF susceptibility testing, antenna and component testing, watt meter calibration and as a driver for frequency multipliers and high power amplifiers.
Rated Output Power: 1.0 watts (minimum).
Input for Rated Output: 1.0 milliwatt (maximum).
Frequency Response: 100kHz - 1000 MHz instantaneously.
Gain: 30 dB (minimum).
Flatness: ±0.5 dB typical, ±1.0 dB maximum.
Harmonic Distortion: Minus 20 dBc maximum at 1.0 W.
Impedance: 50 Ohm.
$ 1075.00 US
|
|  | ARC-116 UHF Power Amplifier, NSN: 5821-00-134-6983 - BRAND NEW
Please visit: www.torontosurplus.com for further details.
This mint RF power amplifier was built for the ARC 116 UHF radio, piggy-backing on the rear of the radio. It covers 225 to 399 MHz. Our units are brand new in the box and originally cost the government over $900.00 ea.
Brand new in original manufacturer's packaging!
Additional Info: FSCM 66423 MFR/PN SM-B-692604
DAAB07-85-C-F094
Dimensions: 5" W, 4 1/2" H, 3/4" D
|
|  | Avantek AK-400N Solid State Amplifier, 200-400 MHz, +15V
$ 125.00 US Please visit: www.torontosurplus.com for further details.
This amplifier has type N (female) connectors for input & output.
2 in stock.
$ 125.00 US
|
|  | Avantek AP-500N RF Amplifier, 250-500MHz
$ 125.00 US Please visit: www.torontosurplus.com for further details.
This amplifier has SMA (female) connectors for input & output.
$ 125.00 US
|
|  | Avantek SM83-2589 Amplifier, 50 - 100 MHz
$ 25.00 each (bulk pricing available) Please visit: www.torontosurplus.com for further details.
Gain 13 dB to 15.5 dB.
89 pieces in stock.
Spec sheet available upon request.
$ 25.00 each (bulk pricing available)
|
|  | Avantek UA82-1678B Solid State Amplifier
$ 85.00 US each Please visit: www.torontosurplus.com for further details.
This 12V amplifier tested at approx. 70 MHz @ 10dB.
2 in stock.
$ 85.00 US each
|
|  | Avantek UA9-1607N Solid State Amplifier, 2-400MHz
$ 85.00 US each Please visit: www.torontosurplus.com for further details.
This amplifier has SMA (female) connectors for input & output.
2 in stock.
$ 85.00 US each
|
|  | Avantek UAA-8747B Unit Amplifier Assembly, 100-500 MHz, +12V
Call for price Please visit: www.torontosurplus.com for further details.
This amplifier has BNC (female) connectors for input & output.
2 in stock.
Call for price
|
|  | EG&G PARC Princeton Applied Research
1218 Solid State Detector Controller
Call for price Please visit: www.torontosurplus.com for further details.
This Controller is for the Model 1211 Interface & 1215 Interface (not available).
There are sockets for these interfaces as well as Detector & Parallel Interface.
BNC Connectors: - Spare, Ext. Sync, Ext. Event, Ext. Analog, CRT X, CRT Y, CRT Z, Comp In, Exp. Start.
Call for price
|
|  | EG&G Princeton Applied Research 5204 Lock-in Amplifier
$ 1,895.00 US Please visit: www.torontosurplus.com for further details.
Options 64-95
Allows both in-phase and quadrature components of a signal to be quickly and easily measured. Measurements can even be taken where signals are obscured by broadband noise, power frequency pickup, other interference, or even if the signal is drifting slowly in frequency.
$ 1,895.00 US
|
|  | EG&G Princeton Applied Research 5207 Lock-In Amplifier
$ 2500.00 US Please visit: www.torontosurplus.com for further details.
Opt 92, 97,98
This Single-Phase Lock-in Amplifier detects and measures very small A.C. signals even when they are obscured by overwhelming noise and interference. Integral RS232C and IEEE-488 interfaces allow for computer control of sensitivity, averaging time constant, phase, operating frequency, offset, dynamic reserve, display mode, and more. The unit includes auto-phasing, auto-ranging, and sine-wave response features as well as digital and analog displays. Full scale sensitivity is 1 µV to 5 Vrms. Input impedance is AC coupled and frequency range is from 5Hz to 200kHz (determined by plug-in cards). Common mode rejection is 120 dB maximum.
$ 2500.00 US
|
|  | Encore 517 Single Ended Amplifier Modules, 830 Power Supply and 4007-127 Modular Instrumentation Rack
$1995.00 US each, Please specify unit Please visit: www.torontosurplus.com for further details.
SPECIFICATIONS:
- Input signal: +/-10V @ X1.0 range & +/-800V @ X0.01 range
- Input impedance: 100k ohms
- Operating modes: DC coupled, AC coupled, zero
- Gain: Switch selectable 1, 2, 5, 10, 20, 50, 100, 200, 500, 1000, plus x1.0/x0.01 range select
- Gain vernier: Continuously adjustable dial
- CMRR: 75dB, DC to 70Hz
- Filter: Four-pole lowpass filter, switch-selectable for 300Hz, 1kHz, 10kHz and Out
- Signal output: ±10V max, 10mA peak load
- Output noise: 10 microvolts RMS RTI max, DC to 20kHz at G=1000
These 517 Amplifiers are in a 4007-127 Modular Instrumentation Rack with a 830 Power Supply
We have 2 Racks:- 1 has: 7 x 517-003 Instrumentation Amplifier Differential Input, With Excitation
- 1 has: 6 x 517-003 Instrumentation Amplifier Differential Input, With Excitation and 1 x 517-002 Instrumentation Amplifier With Excitation
$1995.00 US each, Please specify unit
|
|  | Endevco 2781.10 Amplifier for 2782 Enclosure
Call for price Please visit: www.torontosurplus.com for further details.
Look for our Endevco 2782 Enclosures.
Call for price
|
|  | Endevco 2782 Enclosure with 2781.10 Amplifiers
Call for price Please visit: www.torontosurplus.com for further details.
These enclosures can house up to 13 Amplifiers.
We have 4 units available.
Call for price
|
|  | ENI 440LA RF Power Amplifier
$ 4,500.00 US Please visit: www.torontosurplus.com for further details.
Frequency Range: 150kHz-300MHz
Power Output: 35 Watt Linear (max)
Gain: 45dB (nominal)
Input & Output: 50 N (f) connectors
Applications: Signal and Television distribution as well as Laboratory
$ 4,500.00 US
|
|  | ENI 500L RF Power Amplifier 2-500 MHz, 27 dB, 1 V max
Call for price Please visit: www.torontosurplus.com for further details.
Call for price
|
|  | ENI 503L RF Amplifier
Call for price Please visit: www.torontosurplus.com for further details.
Frequency Range: 2 to 510MHz
Power Output: 3 Watt CW and (PEP)
Gain: 40dB
Noise: 10dB max
Input & Output: 50 ohm BNC (f) connectors on front panel
Applications: Signal and Television distribution (CW, AM, FM, SSB, CATV, and pulse) as well as Laboratory
The photo doesn't do it justice, a better photo is on its way.
Call for price
|
|  | ENI 601L RF Power Amplifier 800 kHz - 1 GHz
Call for price Please visit: www.torontosurplus.com for further details.
- Input Signals: CW, AM, FM, SSB, pulse, wideband sweep, and other complex modulations limited only by their bandwidth and peak input level.
-
Frequency Range: 0.8-1000 MHz
-
Power Output: 1.2 W Linear
-
Gain: 37 dB (nominal)
-
Noise: 9 dB max
-
Input & Output: BNC (f) connectors, 50 ohm
1 in stock
Call for price
|
|  | ENI A300 / A-300 RF Power Amplifier
Call for price Please visit: www.torontosurplus.com for further details.
SPECIFICATIONS:
- Frequency Range: 0.3 to 35 MHz
- Power Output: 500 Watt max CW and Pulse
- Gain: 55 dB ± 1dB variation
- Noise: 10dB max
- Connectors: 50 ohm Type N
1 in stock
Call for price
|
|  | Frequency Electronics Model FE-78B RF Distribution Amplifier
$145.00 US Please visit: www.torontosurplus.com for further details.
This is a 5MHz distribution amplifier (DA) designed to distribute 5MHz to many different devices. It has 2 inputs and 8 outputs. This is a mil-standard device and is ruggedly built. 5MHz (only). Type (N) connectors on the back.
Great for Frequency Standards!!
Excellent condition.
$145.00 US
|
| (Photo shy) |
HP 1111A / Agilent 1111A AC Current Amplifier
$75.00 US Please visit: www.torontosurplus.com for further details.
This is used with HP's AC only series of clamp-on current probes.
$75.00 US
|
| (Photo shy) |
HP 3562A / Agilent 3562A Dynamic Signal Analyzer
$ 3250.00 US Please visit: www.torontosurplus.com for further details.
3563A. It is well suited for test and analysis of mechanical systems and predominantly analog electrical and electromechanical systems. The most significant difference between the two instruments is that the 3562A cannot be used to measure and analyze digital signals and devices.
FEATURES:
- Measurement of analog signals and devices
- Analog signal sources
- Network, spectrum, waveform, transient analysis
- Extraction of models with s- and z-domain curve fitting
- Modeling of systems using frequency response synthesis
- Linear, logarithmic, swept-sine modes
- 64 µHz to 100 kHz
- 80 dB dynamic range with full alias protection
- High accuracy (±0.15 dB)
$ 3250.00 US
|
| (Photo shy) |
HP 462A / Agilent 462A Amplifier
Please visit: www.torontosurplus.com for further details.
Available, photo and details to follow.
|
|  | HP 465A / Agilent 465A Amplifier
$ 185.00 US Please visit: www.torontosurplus.com for further details.
This amplifier provides 20 dB (X10) or 40 dB (X100) voltage gain with flat frequency response from 5 Hz to 1 MHz with floating inputs. The gain accuracy is +/- 0.1 dB, (+/- 1%) at 1 kHz. Input impedance is 10 Mohm shunted by <20pF and Output Impedance is 50 ohm.
$ 185.00 US
|
| (Photo shy) |
HP 467A / Agilent 467A Power Amplifier
Please visit: www.torontosurplus.com for further details.
Available, photo and details to follow.
|
|  | HP 5087A / Agilent 5087A Distribution Amplifier
Please visit: www.torontosurplus.com for further details.
The HP 5087A Distribution Amplifier is a narrow-band amplifier.
We have 2 units in stock, both in very good condition :
Unit A: Configured with 4 x 1 MHz, and 8 x 10 MHz outputs
PRICE - $ 995.00 US
Unit B: Configured with 2 x 1 MHz, 2 x 5 MHz and 8 x 10 MHz outputs
PRICE - $ 1150.00 US
|
|  | HP 7563A / Agilent 7563A LOG Voltmeter/Amplifier
Call for price Please visit: www.torontosurplus.com for further details.
The 7563A is a single-channel, DC logarithmic amplifier with a very high (110 dB) dynamic range designed to produce a logarithmic-related DC output for a very wide range of DC input voltages.
, high input impedance (100 kohm), and low output impedance (5-ohm). Voltage ranges from 316 µV to 100 V.SPECIFICATIONS:
- Input Impedance: 100 kΩ shunted by less than 100pF, single ended
- Output Impedance: Less than 5Ω front panel, 300Ω rear
- Input Voltage ±: 100µV to 100 V
- Output Voltage: 0-1.1 VDC corresponding to 10 mV/dB. Rear Terminals; adjustable 1-10 mV/dB
Call for price
|
|  | HP 8447A / Agilent 8447A - Amplifier 0.1-400 MHz
$ 400.00 US Please visit: www.torontosurplus.com for further details.
Typical 3 dB Bandwith: 50 kHz - 700 MHz
Noise Figure: <7 dB
Output Power for 1 dB Gain Compression: >+6 dBm
Impedance: 50 ohm
VSWR: <1.7.
$ 400.00 US
|
| (Photo shy) |
HP 8447D / Agilent 8447D - Amplifier 0.1-1300 MHz
$ 950.00 US Please visit: www.torontosurplus.com for further details.
Available - Photo and details to follow.
$ 950.00 US
|
|  | IFI 5100 / M5100 Wideband Amplifier 0.1-250 MHz, 10 W
Call for price Please visit: www.torontosurplus.com for further details.
Call for price
|
|  | IFI 5500 Wideband Amplifier 0.01-1000 MHz, 10W
Call for price Please visit: www.torontosurplus.com for further details.
Band 1: 0.01-500 MHz
Band 2: 500-1000 MHz
ALC Input: Selectable, Auto or Man
RF Input & Output
Level Control: Selectable, Remote or Local, with Level Adjustment
Call for price
|
| (Photo shy) |
Kepco BOP 36-5M Bipolar Operational Power Supply / Amplifier with Lambda LM D24 0-+36 B, 0-+5A
Call for price Please visit: www.torontosurplus.com for further details.
This unit is not only a power supply but is also a high-powered operational amplifier with full 4-quadrant, bipolar operation. It's output is capable of sustained d-c as well as the replication of arbitrary a-c waveforms.
Input: 95-113, 105-125, 190-226, 210-250VAC, 47-65 Hz
Output: 0-+36 VDC, +0-5 A, 200 W
3/4 Rack, mounted in Full Rack WITH Lambda LM D24 Power Supply 24 V, 6.7 A
1 in stock.
Call for price
|
|  | Kepco BOP 50-2M Bipolar Operational Power Supply / Amplifier w/ IEEE488 0-0-+50 V (100V pk - pk), 0-0-+2 A
$ 1495.00 US each Please visit: www.torontosurplus.com for further details.
BOP are high speed power operational amplifiers that can be used to provide dynamically agile voltage for test and simulation. They are not general purpose power supplies. By the nature of the bipolar high speed design, they do not have any energy-storage noise discriminating output capacitors.
BOP, while fully rated power supplies, are also high-powered operational amplifiers with full 4-quadrant, bipolar operation. Their output is capable of both sustained d-c and the replication of arbitrary a-c waveforms.
Input: 95-113, 105-125, 190-226, 210-250VAC, 47-65 Hz
Output: 0-+50 VDC, 0-+1 A, 100 W
Our units 3/4 rack, installed in a rackmount frame with 1/4 rack front panel for a finished look & are in Excellent, Mint like used condition.
We have 11 in stock.
$ 1495.00 US each
|
| (Photo shy) |
Kepco BOP 72-5M Bipolar Operational Power Supply / Amplifier +72 V, +5A
Call for price Please visit: www.torontosurplus.com for further details.
This unit is not only a power supply but is also a high-powered operational amplifier with full 4-quadrant, bipolar operation. It's output is capable of sustained d-c as well as the replication of arbitrary a-c waveforms.
Input: 95-113, 105-125, 190-226, 210-250VAC, 47-65 Hz
Output: 0-+72 VDC, +0-5 A, 400 W
Full Rack.
2 in stock.
Call for price
|
|  | M/A-Com MPD Microwave Power Devices LAB-1C-110-4, Solid State Amplifier 100 MHz-1000 MHz, 3 W
$ 2750.00 US Please visit: www.torontosurplus.com for further details.
The unit has 1 each RF Input & RF Output Connectors (type N)
Voltage: 120/220 VAC, 50/60 Hz
$ 2750.00 US
|
|  | Macom MC2016-5-1 GaAs Fet Amplifier
$99.99 US Please visit: www.torontosurplus.com for further details.
Type N connector and an S-Band Waveguide flange
$99.99 US
|
|  | Miteq Amplifier AU-J-3357
$ 85.00 US Please visit: www.torontosurplus.com for further details.
Freq. 1000 MHz In, Out, and +24 V Connections 2 3/4" W, 2" H, 1" D
$ 85.00 US
|
|  | Oxmoor 4X4 Buffer Amplifier
$ 325.00 US Please visit: www.torontosurplus.com for further details.
This is a compact four-channel buffer/mixer/distribution amplifier. Any of the four inputs can be assigned to any (or all) of the four outputs. Two independent mixing buses enable signals to be mixed before or after the gain stages. Front panel controls provide ±15 dB of gain adjustment that may be assigned to the inputs or outputs, and the outputs can deliver +24 dBm to a 600 ohm or higher impedance load. Jumper blocks are used to configure the unit, thus affording complete flexibility with security; nobody can casually re-configure your system by twiddling the knobs.
$ 325.00 US
|
|  | Penta Laboratories PL609 Electron Tube / Power Tube NSN: CG5960-00-451-4287
Call for price Please visit: www.torontosurplus.com for further details.
dimensions approx. 7" diameter Finned section, 5" diameter at screw hole plate, 9 1/2" base to tip (not including leads)
Call for price
|
| (Photo shy) |
PRD Electronics 277 B - Amplifier, Standing Wave Meter
Call for price Please visit: www.torontosurplus.com for further details.
Call for price
|
|  | PRD Electronics 7815 Amplifier, 10-500 MHz
Call for price Please visit: www.torontosurplus.com for further details.
Input Power 115/230 VAC
2 in stock
Call for price
|
|  | Unholtz Dickie D22 PMR Charge/Voltage Amplifier for Accelerometer
$ 395.00 US Please visit: www.torontosurplus.com for further details.
Input: pre amp, accelerometer.
Output: Galvanometer.
FS Range: 1-10K
$ 395.00 US
|
|  | Varian VTC 0667A1 TWT Tube
$ 250.00 US Please visit: www.torontosurplus.com for further details.
| Ew: 1480 VDC |
| Eb: 1480 VDC |
| Ec: 300 VDC
|
| Ef: 17.5 V |
| If: 340 mA |
| Ik: 17.0 mA |
$ 250.00 US
|
|  | Varian X-13 Klystron Microwave Tube / Power Source
Please visit: www.torontosurplus.com for further details.
We have 2 units:
A) NEW - $ 750.00 US
B) USED - $ 300.00 US As-Is, Untested
|
