AccuFiber / Luxtron 100C Optical Fiber Temperature Control System
Used in the following applications: Semiconductor Wafer Processing, Glass Optical Fiber Drawing, Heat Treatment in Induction Furnaces, Sintering, Combustion Research.
Features:

AMCC S4805 S4805CBI DANUBE SONET/SDH STS-48/STM-16 Framer/Pointer Processor, XILINX XC2V4000 Virtex FPGA
We are selling this, basically for the 8 x AMCC S4805 Processors and the Xilinx FPGA which happen to be mounted on the board.  We don't actually have info for the board itself.
The AMCC S4805's sell new for approx. $1000.00 each.

The main components on this board are:

8 x AMCC S4805CBI DANUBE SONET/SDH STS-48/STM-16 Framer/Pointer Processors
Overview and Applications:

• SONET Processing: The S4805 can be used in either SONET or SDH applications. On the low-speed side, it can interface to 4 groups of either 1 STS-12/STM-4 or 4 STS-3/STM-1 signals in each direction.
• Low-Speed Interfaces: On the low-speed side, in both the mux and demux directions, the S4805 supports either a 16-bit wide, 155 Mb/s STS-48/STM-16 signal, a 4-bit wide, 622 Mb/s STS-48/STM-16 signal, 4 serial STS-12/STM-4 signals operating at 622 Mb/s or 4 groups of 4 serial STS-3/STM-1 signals operating at 155 Mb/s. The S4805 is designed to bolt directly to fiber optic transceivers with built-in clock data recovery. (See figure below.)
• High-Speed Interface: On the high-speed side, in both the mux and demux directions, the S4805 supports either a 16-bit wide, 155 Mb/s or a 4-bit wide, 622 Mb/s STS-48/STM-16 signal.
• Controller Interface: A high-speed microprocessor interface is provided for configuration and monitoring. S4805 provides numerous automatic monitoring functions. It can be configured to provide an interrupt to the control system, or it can be operated in a polled mode.
• Applications:
  
• SONET/SDH add/drop multiplexers, terminal multiplexers, and
• WDM/DWDM Mux/Demux applications
  Click HERE for complete info from AMCC
  
  1 x Xilinx XC2V4000 Virtex FPGA
  General Description: The Virtex-II family is a platform FPGA developed for high performance from low-density to high-density designs that are based on IP cores and customized modules. The family delivers complete solutions for telecommunication, wireless, networking, video, and DSP applications, including PCI, LVDS, and DDR interfaces
  Click HERE for complete info from Xilinx
  
  2 x Datum TP313177-000-0 TimePieces
  1 x Datum TP313179-000-0 TimePieces
  2 x Vectron FX-104-DFC-A1P8 Frequency Translators 19.44 MHz

Ando AQ-1934 Optical Sensor, Fiber

Call for price

Ando AQ-1939 Optical Head, Fiber

Call for price

Corning FGM FiberGain Module P/N 0320110004 / 03-0211-00-04 L-Band +18 dBm Booster Amplifier Date 01/16 Rel 04
3 x DB9 F Connectors
3 x DB9 Male Connectors
5 x FIBER CABLES:
IN, OUT (BI:IN), MON, UPB, IN TLV
Call for price

Corning SMF28 SMF-28 Single Mode Optical Fiber, Coat: CPC6
SMF-28 fiber features low dispersion and is optimized for use in the 1310 nm region. SMF-28 fiber also can be used effectively with TDM and WDM systems operating in the 1550 nm wavelength region.

Call for price

E2O Communications EMxxx-L3 Series / EM125-L3TA Fiber Optic Transceiver
These are 3.3V SFF LC Transceiver & 1000Base-SX 850 nm VCSEL for Multimode Fiber.
All are packaged together with a top metal cover and bottom shield. The transmitter consists of a high-performance 850-nm VCSEL while the receiver consists of a GaAs PIN and a preamplifier. All EMxxx-L3 transceivers also include a Signal Detect circuit, which provides a TTL logic high output when a usable input optical signal level is detected.

FEATURES: • 850nm Vertical Cavity Surface Emitting Laser (VCSEL) Source Technology
• Compliant with specifications for IEEE-802.3z Gigabit Ethernet (1000Base-SX) at 1.25 Gbps
• Compliant with ANSI specifications for Fibre Channel applications at 1.06 Gbps
• LC Receptacle Compatible with Industry Standard LC Optical Connector
• Operates with 50 µm and 62.5 µm multimode optical fibers
Data sheet available upon request.
4 pcs in stock, Please advise quantity.
$ 40.00 US each

Fiber Optic Bundle / Lighting Harness

FEATURES:
• Length (end to end): 40"
• Number of Tails: 56
• Emitting Tip 1/8" outer diameter
• Common Threaded End: 3/4" diameter

Fiber Optic Bundle / Lighting Harness

FEATURES:
• Length (end to end): 20X35" 92X47"
• Number of Tails: 112
• Emitting Tip 1/8" outer diameter (some tips are missing the clear plastic lense)
• Common Threaded End: 3/4" diameter

Fiber Optic Bundle / Lighting Harness REF# FB3
This bundle is set-up to accept 3/16" threaded magnifying tips to enlarge the visible light area.
Tips not in stock, but I have included an example in the picture.

FEATURES:
• Length (end to end): 35"
• Number of Tails: 40 approx.
• Emitting Tip Gold Portion: 1/8" outer diameter Red Screw End: 3/16" threaded inner diameter

Fiber Optic Cable with Biconic Connectors - NEW

Fiber Optic Connectors Duplex LC-LC with Dust Cover (both female)
Please specify quantity

Call for price

Finisar FTRJ-1319-1 & FTRJ-8519-1 SFF Laser Fiber Optic Transceiver 2.155 Gb/sec
The 1319 is 1310 nm & the 8519 is 850 nm
Finisar’s new FTRJ-8519-1-2.5 and FTRJ-1319-1-2.5 family of Small Form Factor (SFF) transceiver modules are state-of-the-art components designed expressly for high-speed bi-directional communication applications that require data rates of up to 2.125 Gbit/sec. These transceiver modules will interoperate with 1x and 2x Fibre Channel links, with no Rate Select input required. They are fully compliant with the SFF Multisource Agreement. The 2x5 pinned SFF modules are a cost-effective solution that allows double port densities by fitting twice the number of modules in the same board space. Finisar transceivers feature a very low jitter contribution, which results in extremely clean, high-quality eye patterns.
** Up to 2.125 Gbit/sec bi-directional data links
** Interoperates with 2 Gbit/sec and 1 Gbit/sec data links
** 2x5 pinned RJ-45 footprint Duplex LC connector
** Very low jitter
** Low power dissipation
** Extended operating temperature range
** Metal enclosure for lower EMI
Full specifications available upon request.
We have 2 of each unit in stock.
Call for price

Finisar FTRJ-1320-5 SFF Laser Fiber Optic Transceiver 2.488 Gb/sec
Finisar’s FTRJ-1320-5 Small Form Factor (SFF) transceivers comply with the 2x10 standard package defined by the Small Form Factor Multi-Sourcing Agreement (MSA)1 . They are compatible with SONET OC-48 SR and SDH STM I-16 standards 2 and can also be used for ATM and Shelf-to-Shelf Interconnect.

FEATURES: ** Up to 2.488Gb/s bi-directional data links
** Standard 2x10 pin SFF footprint (MSA compliant)
** Analog diagnostics functions
** Uncooled Fabry-Perot 1310nm laser transmitter
** Duplex LC connector
** Very low jitter
** Metal enclosure, for lower EMI
** Single 3.3V power supply
** Low power dissipation <700mW
** Extended operating temperature range: -10°C to 70°C


Full specifications available upon request.

Units are in Excellent Used condition, please specify quantity required.

Call for price

Fluke FTI / Fotec ACT2 Kit - Fiber Optic Automated Cable Tester for 2 Fibers / DCT Duplex Cable Tester
BRAND NEW!!!
This unit can test two multimode fibers simultaneously for loss at two wavelengths, calculate cable length and store data from the tests for readout on a PC.
The ACT2 can be used for premises cabling and includes a talkset for communication between test crews.
The database memory can hold test data on up to 250 cables and 500 fibers, and cable data can be loaded from a PC before testing. The fiber tester is menu-driven, with four front-panel buttons to allow scrolling.

SPECIFICATIONS:
Wavelengths: 850 and 1300 nm
Fiber: Multimode
FO Connectors: ST (see below)
Loss Measurement Range: 20 dB
Display Resolution: 0.1 opr 0.01 dB
Datalink: RS-232
Dimensions: Each Solo and ACT2 unit measures just 6" x 3.7" x 1.3"
Power: AC Adaptor or 9V Battery

T-ACT2 KIT INCLUDES:
1 Fotec ACT2 Duplex Cable Tester
1 Fotec SOSO Unit
4 Hands Free Earphones for FOtalk
1 A101 Hard Shell Transport Case with Keys
2 Packages of Alco Pads for Cleaning Connectors
2 A108 Battery Charger / Eliminator
1 RS-232 Cable
2 ST/ST, ATC-DCT-62.5 Duplex Multimode Cable Test Kits
1 SC/ST 62.5 Duplex Multimode Cable Test Kit
12 Assorted Fiber Optic Adapters
1 Fotec FOtracer for Tracing Fibers
1 AFT-ST/SC Fiber Optic Testing Guide
1 Quickstart Guide
1 Operating Instructions Manual
1 Software Package V 1.04 (3 disks)
$ 975.00 US

Furukawa Fitel S-146 / S146 Fusion Splicer, SM / MM Fiber
The Fitel S-146 Fusion Splicer is a small compact, portable unit, great for field use or small volume.

FEATURES:
• Built In Heat Shrink Oven
• Splice Single Mode & Multimode Fiber
• DC Operation


Includes: Fusion Splicer, Microscope Lens, Battery Charger, Battery Pack, Carrying Case, DC Power Cord.

HP 10780C / Agilent 10780C Receiver for Laser-Interferometer Positioning Systems

• Typical Power Requirements: +15 volts at 136 mA
• Maximum Sensitivity: 1.5µW
• Dissipation: 2.0 W
• Output Signal: Differential square wave at Doppler-shifted split frequency (100 kHz to 7.2 MHz)
• Usable with a variety of optical components and electronics

JDS Uniphase RA Series 1x8 Fiber Optic Switch RAAW859O01901
The JDS Uniphase RA Series 1xN fiberoptic switch is a single-mode latching switch component for network applications, including network monitoring and optical crossconnects. This component uses fewer switching mechanisms than other 1xN designs.
Collimated beam optics and specially designed prisms yield excellent optical performance. Housed in a hermetic package, the RA Series switch is designed to exceed GR-1221 and meets the requirements of the most demanding central office conditions. The switch is directly mounted on printed circuit boards (PCBs) and comes equipped with status contacts that allow an electrical readout of the switch position.

Key Features:
1x4 and 1x8 bidirectional latching configurations
Hermetic package
Low insertion loss
Null (blocking) state

Applications:
Network monitoring
Bandwidth management applications
Network transmission capacity applications

Additional photos available upon request.
$ 500.00 US

Melles Griot 17 HFB 001 Nanopositioning Fiber Chuck Holder - BRAND NEW
The 17 HFB series of connectorized fiber holders can be used to secure fiber cables with industry-standard connectors to the mounting platforms of nanopositioners and brackets. The center of the connector is positioned 12.5 mm above the platform to provide the appropriate optical axis height.

SPECIFICATIONS:
• Connector: SMA
• Dimensions approx: Base: 32 mm W x 25 mm D, Vertical: 25 mm x 25 mm.

Melles Griot 17 HFB 003 Nanopositioning Fiber Chuck Holder

SPECIFICATIONS:
• Connector: FC/PC
• Dimensions approx: Base: 32 mm W x 25 mm D, Vertical: 25 mm x 25 mm.

Melles Griot 17 HFC 005 Nanopositioning Standard Fiber Chuck - BRAND NEW
The 17 HFC 005 standard fiber chuck is designed to hold bare optical fibers with a nominal outside diameter of 250 µm. It comprises a precision-turned brass body with two end-mounted Teflon collets and small-diameter Teflon sleeve mounted through each collet. The fiber is threaded through the sleeve. The sleeve provides light, but firm, centering pressure on the outside diameter of the fiber and ensures that the fiber is not displaced during tightening.
$ 55.00 US

Melles Griot 17 HFC 007 Nanopositioning Side-Loading Fiber Chuck - BRAND NEW
The 17 HFC 007 side-loading fiber chuck allows bare fibers with a nominal outside diameter of 250 mm to be mounted. It consists of a machined brass body with a 0.2-mm-wide slot to accept the fiber. A crimped spring steel retaining clip holds the fiber in the slot.

Dimensions: 60 mm (2.36 inch) in length and 6.35 mm (0.25 inch) in diameter.
$ 69.00 US

Melles Griot 17 HFG 001 Nanopositioning Standard Fiber Chuck Holder - BRAND NEW
Fiber chuck holders secure fiber chucks (such as the 17 HFC 005 and 17 HFC 007) to the top mounting platform of the nanopositioners or brackets. The 17 HFG 001 standard fiber chuck holder securely mounts a fiber chuck in a three-point location using a nylon-tipped socket-head setscrew. It has a tongue that fits snugly into the slot of a nanopositioner mounting platform and locates the optical axis of the fiber chuck 12.5 mm above the platform.
Dimensions approx: 25 mm x 32 mm x 18 mm
$ 45.00 US

Melles Griot 17 HFG 003 Nanopositioning Adjustable Fiber Chuck Holder - BRAND NEW
Comes with mounting hardware
$ 105.00

Melles Griot 17 HFG 005 Nanopositioning RMS-threaded Fiber Chuck Holder - BRAND NEW
The 17 HFG 005 fiber chuck holder has a male RMS thread, which allows fiber chucks to be mounted to RMS-threaded mounts. The 17 HFG 005 securely holds a fiber chuck in a three-point mount using two nylon-tipped socket-head screws.
Barrel Diameter: 16mm
Barrel Length (not including rms threads): 25 mm
Set Screws: 2 x M3 Nylon Tipped
$ 53.00 US

Newport F-91TS Tilt Stage for Fiber Couplers Model F-915, F-916 & F-91-C1

$ 250.00 US

Newport FP-2 Fiber Optic Positioner - BRAND NEW
FP Series Fiber Optic Positioners provide three or five degrees of precision positioning for bare, connectorized, or polarization-preserving fibers. Bare fibers are positioned using the FP2. Fibers are aligned in three axes (XYZ) using FP-1. Axial Z motion is accomplished without rotation of the fiber by a knurled knob. Fibers are aligned in five axes (XYZ8_x8_y) using the FP-2. Axial Z motion is accomplished without rotation of the fiber by a knurled knob.
$ 225.00 US

Newport FPR2-C1 Fiber Optic Positioner - LIKE NEW
FP Series Fiber Optic Positioners provide three or five degrees of precision positioning for bare, connectorized, or polarization-preserving fibers. Connectorized standard or polarization-preserving fibers are positioned with FPR2-C1. Fibers are aligned in five axes (XYZ8_x8_y) using the FPR2-C1. Axial Z motion is accomplished without rotation of the fiber by a knurled knob.
FPH Chuck not included.
$ 325.00 US

Nortel PP-10G 10 Gb/s PIN Preamp Receiver , Fiber Optic
The PP-10G module consists of a low capacitance photodetector and a low noise GaAs transimpedance amplifier in an hermetic package with a connectorized single-mode fibre pigtail and a 50 ohm  SMA electrical output.

APPLICATIONS:
Long and short reach SONET/SDH systems
Optically preamplified receivers
Datacom systems up to 12.5 Gb/s

FEATURES:
Low capacitance high speed
InGaAs PIN detector
GaAs HBT preamp IC chip
Single polarity power supply
11GHz bandwidth
Wide dynamic range
Hermetically sealed
Bellcore TR-NWT-000468 compliant Complete specifications available upon request.
1 in stock.
$ 250.00 US

NTT NEL A0408FHMLS-A448A Arrayed-Waveguide Grating Multi/Demultiplexer AWG MUX/DEMUX
The arrayed-waveguide grating (AWG) wavelength multi/demultiplexer combines and splits optical signals of different wavelengths for use in WDM systems. The heart of the device, the AWG, consists of a number of arrayed channel waveguides that act together like a diffraction grating in a spectrometer. The grating offers high wavelength resolution, thus attaining narrow wavelength channel spacings such as 0.8nm in ITU channel allocation. Moreover, the multiplexer's extreme stability eliminates the negative effects caused by mechanical vibration; in addition, it delivers long-term reliability because it is composed of silica-based planar lightwave circuits.

MAIN FEATURES:
1) Wavelength Mux / DEMUX for DWDM based on planar lightwave circuit including arrayed waveguide grating(AWG) Many have already been used in practical systems all over the world. An attractive solution for DWDM.
* Narrow channel spacing : min.25GHz
* Large Number of Channels : max.64ch
* Tested to Telcordia GR-1209 and GR-1221

2)Features & Applications
Features
* Narrow and accurate channel spacing
* Large channel number
* Polarization insensitivity
* High stability and reliability

Applications
* WDM transmission
* WDM-based ADM
* Wavelength selective routing
* Optical signal processing

Our A0408FHMLS-A448A units offer:
Channel Spacing: 0.4nm or 50 GHz
Number of Channels: 8
Passband Profile Type: Flat-Top (Wideband)
Temperature Control Element: Heater/RTD
Housing: Pig-Tailed Module
Connector: LC &
Fiber: SMF
Complete specifications available upon request.
Our units are in Excellent Used condition.
$ 750.00 US

Photodyne 22XLA Fiber Optic Multimeter Kit with Model 150 Radiometric Sensor Head
Radiometric Sensor Heads utilize selected, uniform response, large area silicom and gemanium photodiodes as the sensing elements. The elements are all hermetically sealed for long-term stability.

MODEL 150 Sensor:

• Sensor Type: Silicon Photodiode
• Application: General Purpose Low Light
• Active Area (cm²): 0.40 cm² / 0.58 x 0.68 cm
• Power Range: 1 picowatt / 2 milliwatt
• Spectral Cal. (nm): 400-1150 nm / 50 nm interval
• Cal. Set (nm): 900 nm
• Cal. Accuracy %: ±6% 400-900 nm / ±10% 950- 1150nm
• Linearity: ±1
• Power Density: 1 milliwatt per mm²
  
  This set comes with the following:
  
• 22XLA Fiber Optic Multimeter
• Model 150 Radiometric Sensor Head
• 3 x Fiber Adapters
• Charger
• Leads
• Hardshell Case
• Brochure

PicoLight Magnus PL-RCP-00-SD3 / PL-TCP-00-SD3 Parallel Optical Transmitter/Receiver 12 x 1.6 Gbps, SNAP 12
The MAGNUS parallel optical interconnect is a transmitter/receiver pair operating with 12 channels at 1.6 Gbps for an aggregate bandwidth of 19 Gbps.

FEATURES:
• Utilizes a Picolight high reliability, high speed, 850 nm, oxide VCSEL array
• Data rate to 1.6 Gbps per channel for a total link data rate of 19 Gbps
• Mass production compatible FCI Meg-Array connector interface
• Low power consumption (approx. 2 watts per module pair)
• 12 asynchronous independent electrical/optical data channels
• Meets IEEE 802.3z 1000Base-SX std.
• Bit Error Rate < 1x10-12 without FEC
• Supports 50/125 µm and 62.5/125 µm multimode fiber
• Industry standard MTP optical interface
• BGA connector compatible with industry standard wave solder and aqueous wash processes
• 0°C to 80°C operating range
• Single +3.3 V power supply

Schott Fiber Optic Bundle / Lighting Harness

FEATURES:
• Length (end to end): 40"
• Number of Tails: 63
• Emitting Tip 1/8" outer diameter
• Common End: 3/4" diameter

Schott Fiber Optic Bundle / Lighting Harness REF# FB1

FEATURES:
• Length (end to end): 40"
• Number of Tails: 126 approx.
• Fiber Type: Schott LK 1:1 A2-PVC-GN Z-1833 & LK 1:1 A2-PVC-GN Z-1847
• Common End: 3/4" diameter
• Emitting Tip: 3/16" outer diameter

Schott Fiber Optic Bundle / Lighting Harness REF# FB2

FEATURES:
• Total Number of Tails: 126 approx.
• Length (end to end): 42 x 26", 41 x 22", 43 x 19"
• Fiber Type: Schott LK 1:1 A2-PVC-GN Z-1833 & LK 1:1 A2-PVC-GN Z-1847
• Common End: 3/4" diameter
• Emitting Tip: 3/16" outer diameter

Schott Fiber Optic Bundle / Lighting Harness REF# FB4

FEATURES:
• Length (end to end): 34"
• Number of Tails: 125 approx.
• Fiber Type: Schott LK 1 A2-PVC-SW Z-1391
• Common End: 3/4" diameter
• Emitting Tip: 3/16" outer diameter

Silicon Laboratories Si5320ENG-EVB Sonet Clock Engineering Evaluation Board
This board comes with 3 Data Sheets

• Si 5320ENG-EVB Engineering Evaluation Board for Si5320/SDH Precision Clock Multiplier IC
• Si 5320 Preliminary Data Sheet SONET/SDH Precision Clock Multiplier IC
• Si 5364 Preliminary Data Sheet SONET/SDH Precision Port Card Clock IC
  Call for price

Three M 3M Photodyne 22XLC Fiber Optic Multimeter Kit

FEATURES:This unit comes with:
• 1 x 22XLC Multimeter
• 1 x Dual Lead Fiber Optic Cable
• 2 x Model 2003 Adapter Cap for Sensor (not included)
• 2 x 2041 Adapter Cap for Sensor (not included)
• 1 x Fiber Connector
• 1 x 105-129 VAC to 12 VDC Power Supply
• 1 x Carrying Case.
  Close-up photos (including panel function sheet) available upon request.
  $ 350.00 US

Three M 3M Photodyne Fiber Optic Set 9XT, Optical Power Source Drive with 1700-0850-T LED Source

This set comes with the following:

• 9XT Optical Source Drive
• 1700-0850-T LED Source, 850 nm with ST Connectors
• Laser Key
• Charger
• Belt Case
• Hardshell Case
• Manuals (9XT, 1700 LED Source & Operation)

Three M 3M Photodyne Fiber Optic Set 9XT, Optical Power Source Drive with 17XTA Meter, 1700 Series LED Source & More
We have 2 sets:

SET 1 COMES WITH:

• 9XT Optical Source Drive
• 17XTA Fiber Optic Power Meter
• 1 each LED Source: 1700-0850-B, 1700-0850-J, 1700-0850-T
• Laser Key
• Adapter Caps: 2003, 2038-125W, 2019, 2008, 2038-125B (with piano wire), 2 x 2041, 2021, AM-430-20, 2 x 2017
• Sleeves with Drill Bit
• Charger
• Headset
• Hardshell Case
• Manuals: 17XTA, 2230XF (quick instructions)


SET 2 COMES WITH:
-9XT, 17XTA, 1700-0850B, Charger, Laser Key
-Caps: 2038-125B with Piano Wire, 2 x 2041, 1 x 2003, 2 x 2017, 1 x 2021 1 x AM430-45,
-Sleeves with Drill Bit
-17XTA Manual & 2230XF Test Set Quick Reference